Automotive Security & Identification
Tamper-evident, laser-through and durable identification materials for vehicle parts, glass, plates and assemblies…
Solution detailsApplication Solutions
Cross-industry solutions for automotive identification, electronics masking, construction glazing and medical IVD assembly — built from tapes, laminates and die-cut parts.
Application reviewMaterial plus convertingSample timing at quotationExport documents
Solutions
Start with the problem, not the product
Each solution page describes the application, the construction options and the questions to settle before approval.
Electronics Masking & Light Blocking
Light-blocking, masking and precision die-cut tapes for display bezels, FPC bonding, anodizing, plating and electronic…
Solution details
Construction Glazing, Flooring & HVAC
Acrylic foam, foil, double-sided and masking tapes for window glazing, panel bonding, flooring, HVAC sealing and…
Solution details
Medical & IVD Mid-Separator
Medical assembly and IVD mid-separator tapes with stable thickness, clean die-cutting and material selection documented…
Solution details
Battery Tab Holding & Cell Fixing
Adhesive tapes that hold tab protection wires and leads in place during assembly, fix cells inside a module and…
Solution details
Wire Harness Tapes
Wrapping, abrasion protection, noise damping and insulation materials for automotive and industrial harnesses, chosen…
Solution detailsLow-VOC Interior Bonding
Bonding trim, linings, seals and labels inside the cabin, where the substrate is often low-energy or recycled and the…
Solution detailsExterior Trim & Emblem Bonding
Structural tape bonding for badges, mouldings, roof rails, wheel trim and sensor housings on a body that flexes,…
Solution details
Display & Window Bonding
Bonding a cover lens, touch window or display bezel where the joint has to be sealed, survive impact, resist sweat and…
Solution detailsBack Cover Bonding
Fixing a back cover to a mid frame where the joint has to survive shock, dust and liquid, stay out of the way of…
Solution details
Battery Fixing & Removable Bonding
Holding a cell or a module in place while leaving a defined way to take it out again, which is the requirement that…
Solution details
Mirror & Glass Fixing
Fixing mirrors and glass panels to a wall, a frame or a piece of furniture, where the surface behind the glass can be…
Solution details
Window Frame & SDL Bonding
Bonding decorative glazing bars, cover profiles and trim onto a window frame: different materials, outdoor weather, and…
Solution detailsIVD Hydrophilic Film
The top film on a diagnostic strip: it decides how the sample spreads and how fast it moves, and it has to keep doing…
Solution details
Paper Carton Opening Tape
The strip that lets a carton open by hand: a paper-based tape with a pull function, chosen so the box, the closure and…
Solution details
How we work
Material, conversion and validation together
A solution is more than a tape grade. The adhesive, carrier, liner, die-cut edge and application method all affect whether the part works on your line.
- Application and failure-mode review before a material is proposed
- Two or three constructions to compare, with the available data
- Sample or first article for your own test
- Production converting with dimensional and visual checks
- Documents for the selected grade and market
Have a different application?
These pages cover common requests. If your application is not listed, describe the substrates, environment and failure mode — that is enough to start a review.
Solution pages
Match the request to the solution page
Each page below is written around a failure mode or a function rather than around a catalogue family, because that is how the enquiry usually arrives.
| What the request sounds like | Start here | Also read |
|---|---|---|
| We need a label that shows when a part has been opened | Automotive security identification | Die-cut parts and specialty tape |
| Light or solder is reaching a place it should not | Electronics masking and light blocking | Electronics and EMS industry page |
| A window, panel or floor covering has to stay bonded outdoors | Construction glazing, flooring and HVAC | Foam tape and the construction industry page |
| The assay result drifts and the separator thickness is suspect | Medical IVD mid-separator | Medical and IVD industry page |
| Leads and tab protection wires move inside a module | Battery tab holding and cell fixing | New energy industry page |
| The harness rattles, abrades or will not wrap cleanly | Wire harness tapes | Automotive industry page |
When a solution page is not enough
A solution page compresses what we have already seen: the application, the construction options, and the questions to settle before approval. It is a starting point, not an approval document, and the right next step is always a test on your own part.
- Describe the substrates by what is under the tape, not by what the part is called
- Name the failure you cannot accept, since that decides which property has to be tested first
- Say how the part is installed and what the line will tolerate in format and unwind
- Give the annual quantity and the first order, because they change the route more than the grade does
- Send the drawing or a photograph if a shape is involved; a laser prototype and a tooled part are different conversations
FAQ
Solution questions
Do you work on applications not listed here?
Yes, regularly. The six pages cover the requests that arrive most often. When an application is outside them, we review it as an assembly problem and say whether it is an existing construction, a laminate of two, or something that needs a material we do not currently carry.
Can one solution combine several tape families?
That is the normal case rather than an exception. A battery module can take an insulation film, a thermal interface and a holding tape in the same assembly, and a harness wrapping job usually compares cloth, foam and PET before anything is fixed.
What do you need to start a solution review?
The two surfaces, the load or function, the environment and the failure mode. A drawing, a photograph of the joint or the brand grade you use today all help; none of them are required to begin.
Is a solution page a guarantee that it will work for me?
No. It records what has worked and why. Adhesive performance belongs to the substrate, the preparation, the method and the service conditions, so approval comes from your own test on your own product.
Describe the failure you cannot accept.
We will propose a construction and a test plan around it.